Roksan Audio Stereo System MK III User Guide

Kandy  
AM / FM TUNER  
MkIII  
U S E R M A N U A L  
R O K S A N A U D I O L I M I T E D  
6 NORTHFIELD INDUSTRIAL ESTATE  
BERESFORD AVENUE  
MIDDLESEX HA0 1NW  
ALPERTON  
ENGLAND  
T E L .  
F A X .  
+ 4 4 ( 0 ) 2 0 8 9 0 0 6 8 0 1  
+ 4 4 ( 0 ) 2 0 8 9 0 0 6 8 0 2  
+ 4 4 ( 0 ) 2 0 8 9 0 0 0 7 3 4  
 
CAUTIONS  
K a n d y Integrated Amplifier  
AC MAINS SUPPLY  
Your Kandy Integrated Amplifier is set to operate from a fixed supply voltage which is marked on a label next to  
the mains input plug. Before connecting the mains lead please check that your mains supply corresponds to this  
label as below:  
230V Products ………………………………….Voltage Range: 220V – 240V  
115V Products ………………………………….Voltage Range: 100V – 120V  
The mains lead supplied with this product has an IEC mains socket which plugs into the IEC connector on the  
unit’s rear panel. The other end is normally attached to the appropriate mains plug for your country. In the UK  
this is the standard UK13A plug.  
This plug should ordinarily not be removed from the lead. If you do remove it, please dispose of it safely so that it  
cannot be plugged into a mains socket whilst in a potentially dangerous condition. We suggest that you obtain  
from your dealer a complete replacement lead.  
Should you move to another area where either the mains voltage or the mains plugs are different from those as  
supplied with your Integrated Amplifier, please contact the appointed ROKSAN distributor for assistance.  
Please observe correct mains polarity at all times.  
The Integrated Amplifier mains fuse is located on the rear panel next to the IEC mains connector. This must only  
be replaced by the fuse of the type and rating as described on the fuse rating label on the rear panel of the unit.  
This product requires connection to earth (ground). The earth wire (in the UK this is colour coded green/yellow)  
of the mains cable supplied with your Integrated Amplifier must be connected to a suitable earthing point  
established for this purpose by your electricity supply company. If you are in any doubt, consult a qualified  
electrician.  
If the equipment is likely to be unused for some time, unplug it from the mains supply.  
GENERAL CAUTIONS  
FCC WARNING  
This equipment may generate or use Radio Frequency energy. The user may lose the right to operate this  
equipment if unauthorised modifications are made.  
INTERFERENCE  
Properly installed, this unit should not cause harmful interference to radio communications, There is, however, no  
guarantee that such interference will not occur in a specific installation. If interference arises (which you can  
determine by switching the unit off and on) you could try to remedy matters by the following:  
Re-orient or re-locate the receiving antenna  
Increase the distance between the Kandy Integrated Amplifier and receiver  
Connect the unit to a different mains circuit from that of the receiver  
Consult your ROKSAN appointed dealer or an experienced Radio/TV technician for help and advice  
LOCATION  
Your Kandy Integrated Amplifier should be located in a well ventilated area and kept away from sources of heat,  
dust and humidity and from direct sunlight.  
The Integrated Amplifier may be positioned either as a free standing unit or alongside another audio/video  
product.  
Never place the Integrated Amplifier on carpet or any surface likely to hinder normal ventilation.  
Never allow liquids or other objects to fall into the unit.  
This unit contains no user serviceable parts. Do Not remove any panels or attempt to service it yourself.  
Unauthorised servicing will void the warranty.  
Roksan Audio ltd  
Kandy Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.0  
All specifications are liable to change without notice. E&OE  
Page 3 of 8  
ENGLISH  
 
INSTALLATION  
K a n d y AM / FM Tuner  
ROKSAN Kandy Tuner - Front Panel View  
1
2
3
4
5
6
7
8
ST/MONO  
MUTE  
ROKSAN  
POWER  
BAND  
PRESET  
AUTOSCAN  
TUNE/SELECT  
AM / FM TUNER KT-I MkIII  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
Mains AC Power Button  
Band Selection Button  
FL Display  
Preset Button  
Stereo / Mono Button  
Tunning / Selection Knob  
Mute Button  
Autoscan Button  
ROKSAN Kandy Tuner - Rear Panel View  
1
2
3
4
5
1.  
2.  
3.  
4.  
5.  
FM 75 Antenna Input  
AM Antenna Input  
Analogue Output (Left & Right)  
IEC Mains Inlet Socket  
Voltage & Fuse Rating Label  
SETUP  
K a n d y AM / FM Tuner  
CONNECTING MAINS POWER  
The moulded IEC connector of the supplied mains lead should be plugged into the socket (4) on the  
rear of the unit first and then plugged into the mains supply. The Mains power switch (1) is on the front  
panel of the Tuner. Your Tuner should be switched off when not in use and if it is to be unattended for  
a long period, it should be switched off and the mains lead unpluged from the wall.  
Roksan Audio ltd  
Kandy Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.0  
All specifications are liable to change without notice. E&OE  
Page 4 of 8  
ENGLISH  
 
ANTENNA CONNECTIONS  
FM Antenna:  
Connect the adaptor & the ‘T’ FM Antenna supplied to the antenna socket (1)  
on the back panel. (NOTE: A high quality indoor or out door FM aerial can  
improove the performance of your Kandy Tuner)  
AM Antenna:  
Connect the AM Antenna supplied to the antenna sockets (2) on the back  
panel. (NOTE: A high quality AM aerial can improve the performance of your  
Kandy Tuner).  
IMPORTANT NOTE: For optimum performance it is recommended to use high quality inter-connect cables such  
as ROKSAN HDC-02A High Definition Analogue Cable and ROKSAN HDC-01D High Definition Coaxial Cable  
for aerial extensions.  
OPERATION  
K a n d y AM / FM Tuner  
SWITCHING ON  
The Mains power switch (1) is located on the front panel of the Tuner. When switched ON, your Kandy  
Tuner FL Display will illuminate with the word ‘ROKSAN’ for a few seconds it will then revert to the  
previously selected preset.  
USING THE CONTROLS  
BAND SELECTION  
Press the Band Selection Button (2) on the front panel to toggle between FM and AM. Notice on the  
display the frequency indication will change from MHz to kHz and the preset indicator will also change  
from ‘F’ to ‘A’ for FM and AM respectively.  
AUTO/MANUAL SCAN  
Press the Auto-scan Button (8) on the front panel to toggle between scan tuning and manual tuning.  
Notice on the display if ‘AUTO’ is lit. If so by simply turning the Tune/Select Knob (6) by approximately  
a ¼ turn clockwise or anti-clockwise, the tuner will automatically scan up or down until a strong enough  
signal is detected. It will then stop at that frequency and if it happens to be a desired radio station, you  
can store it in one of the preset memories. Otherwise, just turn the knob a little again and the tuner will  
search for the next strong signal and so on.  
In manual mode (‘AUTO’ not illuminated) turning the Tune/Select Knob will advance up or down the  
tuning frequency to allow you select your desired radio station.  
PRESET SELECTION  
Press the Tune/Select Knob (6) to toggle between tuning and preset selection. Notice when preset  
selection is chosen the preset indicator and memory indicator ‘MEM’ flash. Simply turn the knob anti-  
clockwise to go back and clockwise to go forward to your desired preset (For example the 5th preset  
location: 05F). Once on the desired preset, press the knob again to complete your selection.  
PRESET PROGRAMMING  
You can programme up to 99 presets to your favourite radio stations. Once you have selected a radio  
station, press the Preset Button (4); the preset indicator and memory indicator ‘MEM’ start to flash.  
Simply turn the Knob (6) until you get to the desired preset number that you wish to store this station in  
(For example the 11th preset location: 11F or 11A if storing an AM frequency) and press the Preset  
Button again to store and complete your selection.  
Page 5  
Roksan Audio ltd  
Kandy Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.0  
All specifications are liable to change without notice. E&OE  
Page 5 of 8  
ENGLISH  
 
STEREO / MONO SELECTION  
Press the St/Mono Button (5) on the front panel to toggle between Stereo and Mono (while you are  
listening to a stereo FM broadcast). This is a useful feature especially when tuned to a ‘weak’ radio  
station with excessive background noise. To reduce this background noise, simply select Mono which  
increases the tuner’s signal to noise ratio.  
MUTE SELECTION  
Press the Mute Button (7) on the front panel to toggle between Muted and normal audio output. Notice  
when mute is selected the display will show ‘MUTE’ and the audio put puts are muted completely.  
Press the mute button again to revert to the previously selected radio station with unmated audio out  
put.  
REMOTE CONTROL  
K a n d y AM / FM Tuner  
Your Tuner is supplied with a Kandy MKIII System  
Remote Handset.  
The Remote Control Handset is powered by two 1.5V AA  
batteries (supplied). When inserting the batteries observe  
the correct polarity.  
The handset duplicates all front panel controls (except  
mains AC power switch) and contains some additional  
features.  
3
4
7
8
1
2
5
6
1
2
3
4
5
6
7
8
9
PRESET UP  
PRESET DOWN  
FREQUENCY INPUT  
AM/FM BAND SELECTION  
TUNE DOWN  
TUNE UP  
MUTE  
9
10  
MEMORY STORE  
NUMERIC KEYS  
10 TUNER NUMERIC KEY  
SELECTOR  
NUMERIC KEYS  
1. To activate the Numeric Keys (9) for the Tuner press TU.# Button (10).  
2. To enter any digit (for example the station Frequency) press corresponding digits from the  
Numeric Keys (9).  
FREQUENCY  
Pressing the Freq. Button (3) lets you enter the station frequency directly from the numeric key pad  
without scanning up or down.  
Roksan Audio ltd  
Kandy Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.0  
All specifications are liable to change without notice. E&OE  
Page 6 of 8  
ENGLISH  
 
1. Press the Freq. Button (3) the display will blank the frequency digits ready for entering the new  
ones.  
2. Enter the corresponding digits from the Numeric Keys (9).  
GUARANTEE  
K a n d y AM / FM Tuner  
There are no user-serviceable parts inside your Kandy Tuner. If a fault should develop, refer any servicing to  
your appointed ROKSAN dealer, distributor or ROKSAN approved service agent.  
Your ROKSAN Kandy Tuner is guaranteed against any defect in materials and workmanship for a period of two  
years from the date of purchase.  
This guarantee only becomes effective if the warranty card is validated by the ROKSAN retailer from whom the  
equipment was purchased and returned to ROKSAN within 28 days of purchase.  
This guarantee excludes:  
1. Damage caused due to accident, misuse, neglect and incorrect installation, adjustment or repair.  
2. Liability for damage or loss during transit from the retailer or purchaser to ROKSAN or its authorised  
distributor for the purposes of repair or inspection.  
Carriage costs to ROKSAN shall be borne by the consignor.  
All claims under this guarantee must be made through an authorised ROKSAN retailer.  
If equipment returned for repair to ROKSAN is found on inspection to comply with the product specification  
ROKSAN reserves the right to make a charge for examination and return carriage.  
Unauthorised servicing will void this guarantee.  
SPECIFICATIONS  
K a n d y AM / FM Tuner  
Number of presets  
99  
Audio Output (@ 75kHz Dev. Mono 1kHz)  
1.3 V  
Aerial Input  
FM 75Coaxial  
AM Quick Connect Terminals  
S/N Ratio (CCIR – ARM)  
FM:  
AM:  
Mono >75dB  
Stereo >69dB  
>50dB  
THD+N @ 1kHz 775mV (400Hz HPF, 30kHz LPF)  
Mono, 75kHz Deviation <0.4%  
Stereo, 75kHz Deviation <0.5%  
Sensitivity (IHF)  
Tuning Range  
11dB µ  
FM:  
AM:  
87.5 – 108 MHz  
522 – 1611 kHz  
Frequency Response (FM)  
Power Source  
20Hz - 15kHz (-1dB)  
220V – 240V 50Hz / 60Hz  
100V – 120V 50Hz / 60Hz  
Power Consumption  
Dimension  
<17 W  
432 x 380 x 90 (W x D x H) mm  
432 x 380 x 102 (including feet)  
Weight  
7Kg  
Roksan Audio ltd  
Kandy Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.0  
All specifications are liable to change without notice. E&OE  
Page 7 of 8  
ENGLISH  
 
NOTES  
K a n d y Integrated Amplifier  
Kandy Integrated Amplifier MKIII  
Serial Number: …………………………  
Year .……… Month …….. Day ……..  
Purchase Date  
ROKSAN Retailer  
Name:  
…………………………………  
Location: ………………………………  
Please keep a record for future reference  
w w w . r o k s a n . c o . u k  
Roksan Audio ltd  
Kandy Integrated Amplifier User Manual  
CLASSIFICATION: General Use  
Version 3.0  
All specifications are liable to change without notice. E&OE  
Page 8 of 8  
ENGLISH  
 

Radio Shack Cordless Telephone ET 1105 User Guide
Roberts Radio Portable Radio R9965 User Guide
RocketFish Power Supply RF 700WPS2 User Guide
Royal Sovereign Laminator ES 1315 User Guide
Russound Stereo Amplifier CA44pi User Guide
Samson Stereo Amplifier S63, S83 User Guide
Sanyo Refrigerator HF 502 User Guide
Sanyo Refrigerator MPR 311DH User Guide
Sanyo Refrigerator MPR 715F User Guide
Senco Nail Gun SCN40DW User Guide